-
5
-
4
-
2利用显示动力学做钻头冲击的模拟,在试样的下方开了一个预制裂纹,但是在计算过程中,钻头碰到试样后就被弹飞,往相反的方向运动了。请问各位大佬这是怎么回事
-
10我想问一下如何查看轧制力啊,我在轧辊中心参考点设置了一个set,可是为什么输出的轧制力正负值交替变化啊,愁死了,求大神指点
-
0有大佬知道如果通过滞回曲线得到结构的等效阻尼比吗?
-
1在abaqusGUI运行脚本,重复执行:打开odb文件-关闭操作,只要不关闭GUI,即使脚本运行结束,运行期间占用的内存也不会释放(不过这部分占用内存会在GUI关闭时释放)。我只测试了仅打开关闭操作下的内存情况,不过可以预计,期间的其他操作会进一步加重内存异常占用的情况。求解答是为什么?
-
1
-
0
-
3
-
2哪位大佬可以帮忙做个动荷载路基沉降模拟,有偿私我
-
1
-
0
-
10
-
1是在面上加变压力还是用流体荷载来做,并且用流体的话动力隐式没法施加
-
1大佬们abaqus里用CEL法 做射流破土 入口水流不扩散 但破土效果还行 能作为硕士毕业论文模型吗 太焦虑了老师不管 求大佬指明路
-
10报下面的错误如何解决 ABAQUS error:there no keywords defined in the input file
-
0刚接触abaqus软件,需要做搅拌摩擦焊和焊接的枳构模拟,有偿求教#搅拌摩擦焊#abaqus
-
1
-
4
-
8Tabular data for at least one option or suboption has either blank or zero value rows
-
4
-
0
-
2
-
8
-
10报错:ERROR: Visual Studio 2019 is not found in the system. 应该如何解决?
-
1大家注意!!!名工仿真有限元工作室代做骗人,做的东西一分不值全是错的,收我2500。不给退款,威胁人要给学校打电话让我毕不了业,还泄露个人隐私,曝光他。有上当受骗的大家一起交流举报![图片][图片][图片][图片][图片][图片][图片][图片][图片]
-
0
-
13
-
75The elements contained in element set ErrElemExcessDistortion-Step1 have distorted excessively. The elements in element set ErrElemZeroALEMass-Step1 have zero or negative mass. Print-out suppressed for subsequent distorted elements There are a total of 4346 excessively distorted elements The elements contained in element set ErrElemExcessDistortion-Step1 have distorted excessively. Abaqus/Explicit Analysis exited with an error - Please see the status file for possible error messages if the file exists.
-
0模型是在hypermesh中已经画好的钢轨,我需要在钢轨两端施加无限元防止波的反射。找答疑或代做。#abaqus##hypermesh#
-
5
-
2请教大佬们,Abaqus欧拉法计算的结果除去各种云图外,有什么办法能输出特定位置的温度或PEEQ变化曲线吗?我学了教程说做不到,但是的确从别人文章里面看到了用欧拉法结果输出了曲线。 求教求教。 附文献链接https://doi.org/10.1016/j.jmrt.2024.04.057
-
1模型总是不收敛,要是有显式分析就好了
-
0在abaqus中测定玻璃材料的力学性能,属性里面怎么去定义脆性材料。
-
18A boundary condition has been specified on node set assembly__pickedset298 but this node set is not active in the model A boundary condition has been specified on node set assembly__pickedset298 but this node set is not active in the model A boundary condition has been specified on node set assembly__pickedset298 but this node set is not active in the model A boundary condition has been specified on node set assembly__pickedset298 but this node set is not active in the model A boundary condition has been specified on node set assembly__pickedset298 but this node set is not active in the model
-
6
-
24
-
1我想把两个立方体tie起来,然后中间就有面重合,请问能不能把中间相接的线除去看起来像一个整体啊
-
89在输入27800@计算机名 步骤后, 出现“ Your Abaqus license server is running with an unsupported version of FLEXnet. Established Products require an ABAQUSLM vendor daemon 11.13 or later. We recommend that you input a license server with the correct level ABAQUSLM vendor daemon. Select 'OK' to enter a different server, or select 'OK', then 'Back', and then select 'Skip licensing configuration'. ” 我查看了下环境变量,发现true是大写的,改为小写后依然不行。请问该怎么办?
-
1请问各位大佬,在hypermesh中划分好的网格导入abaqus中,怎么把他定义为欧拉体呢
-
0
-
2提交作业时一直显示这个错误,看以前的帖子加环境变量时找不到command路径,然后在安装路径中搜索command找了个路径D:\CAE\win_b64\code\command,不清楚环境变量名是什么用了Path,path,abaqus modify windows error2反复试了好几次,但依然有那个报错,麻烦各位大佬帮忙看看怎么解决这个问题
-
3
-
2
-
3
-
69小白已经装了三遍了……累觉不爱 Abaqus License Manager checked out the following license: "cae" from Flexnet server localhost <1023 out of 1024 licenses remain available>.*** Error: ABQcaeK.exe / rank 0 / thread 0 encountered a system exception 0xC0000005 (EXCEPTION_ACCESS_VIOLATION)GUI detected error while waiting for ipc connection to close. *** ABAQUS/ABQcaeG rank 0 received the SIGABRT signalAbaqus Error: Abaqus/CAE Kernel exited with an error.